Fluke 113 True-RMS Utility Multimeter


  • Digital multimeter measures AC/DC voltage, resistance, and capacitance and performs continuity and diode tests
  • True RMS meter provides accurate readings when measuring linear or nonlinear loads where the current or voltage has a sinusoidal or nonsinusoidal waveform
  • Simultaneously checks for voltage and continuity
  • Manual and auto ranging modes for user flexibility
  • Safety rated for Category III to 600Volts and Category IV to 300 Volts

Out of stock

SKU: B01EWFE6XK Category:

Product description


The Fluke 113 True-RMS Utility Multimeter is a digital multimeter (also known as a multitester) that measures AC/DC voltage to 600V, resistance to 60 kiloohms, and capacitance to 9,999 microfarads. The meter has a diode check for testing general-purpose germanium, silicon, and power diodes, and a continuity beeper which provides audible detection of resistance by turning on at less than 25 ohms and off at 250 ohms. It is also able to simultaneously check for voltage and continuity. This true RMS meter provides accurate readings when measuring linear or nonlinear loads where the current or voltage has a sinusoidal or nonsinusoidal waveform and has both manual- and auto-ranging capabilities for user flexibility. A Max/Min function records signal fluctuations and a hold function freezes measurements on the display. The 6000-count resolution, 3-1/2 digit digital display is backlit for readability in low-light conditions. The meter is safety rated for Category III to 600V and Category IV to 300V. It uses a 9V battery (installed) with a battery life of approximately 300 hours without backlight and has a sleep mode to maximize battery life. The meter measures 6.58 x 3.35 x 1.81 inches (H x W x D) and weighs 13 oz./404 g. (H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.) This meter includes a holster with built-in probe holders for convenient storage.

Multimeters are electrical test meters that measure multiple properties of an electrical circuit, such as current, voltage, resistance, capacitance, and continuity. Available in handheld or benchtop models, multimeters diagnose electrical problems in electrical equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Multimeters display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltage. Safety ratings are based on International Electrotechnical Commission (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating.

Fluke Corporation manufactures electrical testing tools and software for industrial and commercial applications. The company, founded in 1948, is headquartered in Everett, WA.

What’s in the Box?
  • Fluke 113 utility multimeter
  • Test leads
  • 9V battery
  • Instructions

From the manufacturer

Digital Multimeters: When Uptime Matters

Fluke Digital Multimeters (DMM’s) are on more tool belts, finding more problems, than any other comparable test tools. Each design is tested to the extreme: drop, shock, humidity, you name it. Every Fluke Digital Multimeter gives you what you need: accurate measurements; consistent, reliable performance; attention to safety.

Fluke 113 Digital Multimeter

The Fluke 113 Digital Multimeter gives users the means to quickly and easily do basic meter set and reconnect testing. This meter is simple-to-use and has the features needed to repair most electrical problems. The Fluke 113 has significant improvements over other digital multimeters available on the market, including Fluke model 7-600. Using the Fluke VCHEK LoZ low impedance measurement function, users can simultaneously test for voltage or continuity. The Min/Max function lets you record signal fluctuations. The Fluke 113 can perform diode tests, and also provides both auto and manual ranging capabilities. With features such as conformance to the latest safety standards, backlight, and a much larger display that’s easier to view, this meter is a must have for every toolbox.

  • VCHEK LoZ low impedance measurement function to simultaneously test for voltage or continuity
  • True RMS for accurate AC measurements on non-linear loads
  • A large backlit display allows for easy visibility in low-lit areas
  • Record signal fluctuations using the Min/Max function


There are no reviews yet.

Be the first to review “Fluke 113 True-RMS Utility Multimeter”